Scanners
You can answer that in two minutes without asking us. Open the browser on the scanner and load app.stocktakesonline.com. If the sign-in page appears, the device can reach the portal — and on Android 5.1.1 or newer, the app will run on it.
The hard part on an older scanner is not the app — it is whether the device still recognizes the security certificate the portal uses, from a list built into it when it was made and never updated since. The browser checks exactly that, which is why this test is worth more than our list.
Stocktakes Online is an Android app for Zebra rugged scanners, from the compact TC22 to the cold-storage MC9400. It runs on Android 5.1.1 and newer, which is most of what is sitting in American drawers — so the scanners you already own are probably enough.
| Run on these | Android | What that proves |
|---|---|---|
| Zebra TC8000 | 5.1.1 | 2015 hardware and the oldest we have counted on. Also the floor — below 5.1.1 the app will not install |
| Zebra TC56 | 8.1.0 | Counted to the portal and withdrew a count again, November 2026, on a device of our own. It fills the gap between 5.1.1 and 11, and it is the first of the TC5x family we have run — the nearest relative to the TC52 and TC57 in the untested list below |
| Zebra MC3300x MC330L-GJ3EG4RW | 11 | Scanned to the server on a colleague's own device, October 2026. MC330L is the MC3300x; the original MC3300 is MC330K or MC330M, which we have not run |
| Zebra MC9300 series MC930B-GSCDG4RW | 13 | Same day, same result — and this one shipped years ago on an older Android, so it is also proof that updating a scanner beats replacing it |
| Zebra MC3400 | 14 | A full two-site count, October 2026. This is the device it is built on |
| Zebra MC9400 2D-ER | 14 | The same count. Its extended-range imager also reads a label on a sheet of paper from a few centimeters, which a long-range scanner is not supposed to do |
That is the whole list, and it is short on purpose. Six devices spanning Android 5.1.1 to 14 is nine years of hardware, which tells you more than a longer list would: the app does not care what the model is, it cares that the scanner hands a barcode to the screen as typed text. The part numbers are there so you can match yours exactly — read it off the back of the device, or off your asset register.
Everything else Zebra makes on Android 5.1.1 or newer should work, and you can prove it in two minutes without us — open the browser on the scanner and load app.stocktakesonline.com. If the sign-in page appears, the device can reach the portal. The hard part on an older scanner is not the app; it is whether the device still recognizes the security certificate the portal uses, from a list built into it when it was made and never updated since. The browser checks exactly that.
And the test that settles it is a count, not a scan. Check Products and Check Locations only read from the portal; a count writes to it, and that is a different path. A device can read perfectly and still fail to write — we have seen exactly that on a scanner of our own, which is why “it scans” is not the test. Install the app, count one item, and look for it on the dashboard.
Not run by us yet — the range the app is built for, which is exactly why the test above exists.
What will not work, so you don't spend an afternoon finding out. There are two reasons a Zebra is out, and both are the operating system rather than the scanner.
It isn't Android. Every Windows CE and Windows Mobile scanner is out — Windows Mobile 5.0, 6.1 and 6.5, and every version of CE. That is the MC9090 and MC9190, the MC3090 and MC3190, the MC55, MC65, MC67 and MC75, and the WT41N0. If it starts up into Windows, Stocktakes Online cannot run on it, and no update changes that — Zebra ended support for those operating systems years ago. The two-minute test above will point you the wrong way here: the browser on those devices is far too old to recognize the portal's certificate, so you get a security warning and conclude that is the problem. It isn't. The device cannot run an Android app at all.
It is Android, but below 5.1.1. The app will not install, and on these there is no newer Android to move to. The MC3200 (MC32N0) shipped on Android 4.4. The TC55 shipped on 4.1.2 and was never taken past 4.4.3. The MC40 stops at 4.4.4. Those are Zebra's own numbers, and none of the three has an update that reaches 5.1.1, so there is nothing worth trying. Here the test above passes — the certificate is fine, it is the app that will not install, which is exactly why these three are worth naming.
One that looks like it belongs here and doesn't: a TC70 or TC75 still on KitKat. Zebra released Android 5.1.1 for both, so the operating system on it today is not the limit — updated, it clears the floor. Worth checking before you write either one off.
Tell us the model number and we'll tell you straight whether we have run it. We say which ones we have tested and which we have not, because a scanner that turns out not to work on count night is not a small problem.
Honeywell, Datalogic and the rest. The app needs the scanner to hand a barcode to the screen as typed text ending in Enter, which every industrial Android scanner can do — but each brand sets it up in its own utility, and we have only done it on Zebra. Ask about yours and we'll work through it with you.
We've sold and supported Zebra hardware for thirty-five years, and we'll spec the right unit for your aisles, your freezer and your budget — that advice is free and it's the part we're good at.
In the United States there is nothing behind that advice we could sell you. Zebra's own locator will find a reseller near you.
Still not sure? Send us the model number. Read it off the back of the device or off your asset register — something like MC330L-GJ3EG4RW — and we will tell you straight whether we have run it, whether we expect it to work, or whether it is below the Android floor. We say which ones we have not tested rather than implying we have.